Mechanical Properties of Solids NEET Notes and Important Questions (Class 11 Physics)
Quick NCERT-based revision of Mechanical Properties of Solids for NEET: stress and strain types, Hooke's law, the stress-strain curve, Young's, shear and bulk moduli, Poisson's ratio, elastic energy and I-beams, with a formula table, NEET traps and 8 MCQs.
By Anmol Sharma16 min read

Mechanical Properties of Solids: key highlights
| Particulars | Details |
|---|---|
| Class and chapter | NCERT Class 11 Physics, Chapter 8 |
| Unit | Properties of Bulk Matter |
| Key topics | Elasticity and plasticity, stress and strain, Hooke's law, stress-strain curve, Young's, shear and bulk moduli, Poisson's ratio, elastic potential energy, applications |
| How NEET asks it | Numericals on elongation, bulk strain and energy density; stress-strain curve points; match moduli with deformation; statement-based |
| Revision time | 35-45 minutes for these notes |
In one line: Within the elastic limit, stress = modulus × strain, and the type of stress (tensile, shearing or hydraulic) decides which modulus (Y, G or B) you use.
📲 Get the TrackPrep app on Google Play: practise, take mocks and ask Jojo on your phone.
Table of contents
- Download the NCERT PDF
- Short notes for quick revision
- Important tables and comparisons
- Diagrams to revise
- NEET traps in this chapter
- Practice questions
- Answer key
- Practise Mechanical Properties of Solids on TrackPrep
- Frequently asked questions
Download the NCERT PDF
| Book | Chapter | Official PDF |
|---|---|---|
| NCERT Class 11 Physics | Chapter 8: Mechanical Properties of Solids | 📥 Download Mechanical Properties of Solids NCERT PDF (ncert.nic.in) |
Read the official NCERT chapter alongside these notes. Every note and question on this page is based on it.
Short notes for quick revision
Elasticity and plasticity
- Solids are not perfectly rigid; enough force deforms even a steel bar.
- Elasticity: property by which a body regains its original size and shape when the force is removed (helical spring). The deformation is elastic deformation.
- Plasticity: no tendency to regain shape; permanent deformation. Putty and mud are close to ideal plastics.
Stress
- When a deforming force acts, a restoring force develops, equal and opposite to the applied force.
- Stress = restoring force per unit area = F/A.
- SI unit N m⁻² or pascal (Pa); dimensions [ML⁻¹T⁻²].
- Tensile stress (stretching) and compressive stress (compressing) together = longitudinal stress.
- Tangential (shearing) stress: forces parallel to the cross-section.
- Hydraulic stress: body in a fluid under pressure; force normal to every point of the surface; equal in magnitude to the hydraulic pressure.
- Stress is not a vector: it cannot be assigned a single direction.
- A wire hanging from a ceiling with weight F: tension at any section is F, not 2F, so stress = F/A.
Strain
- Longitudinal strain = ΔL/L.
- Shearing strain = Δx/L = tan θ ≈ θ (θ small; at θ = 10°, θ and tan θ differ by only about 1%).
- Volume strain = ΔV/V (hydraulic compression changes volume, not shape).
- Strain is a ratio: no units, no dimensions.
Hooke's law
- For small deformations, stress ∝ strain: stress = k × strain; k = modulus of elasticity.
- An empirical law, valid for most materials; valid only in the linear part of the stress-strain curve.
- Elastomers (rubber, tissue of aorta) do not obey Hooke's law over most of their elastic region.
Stress-strain curve (metal under tension)
- O to A: linear; Hooke's law obeyed; body regains shape (elastic).
- A to B: not proportional, but the body still returns to its original dimensions.
- B = yield point (elastic limit); stress here = yield strength σy.
- B to D: strain rises rapidly for small stress increase. Unloading at C leaves strain at zero stress: permanent set, plastic deformation.
- D = ultimate tensile strength σu. Beyond D, strain increases even with reduced force; fracture at E.
- D and E close → brittle; D and E far apart → ductile.
- Aorta tissue curve: very large elastic region, does not obey Hooke's law over most of it, no well-defined plastic region.
Young's modulus (Y)
- Y = tensile (or compressive) stress / longitudinal strain = (F × L)/(A × ΔL).
- The strain is the same for a given material whether the stress is tensile or compressive.
- Unit N m⁻² (Pa). Metals have large Y: large force for a small change in length.
- Same 0.1% strain in a wire of 0.1 cm² area needs 2000 N for steel, 1100 N copper, 900 N brass, 690 N aluminium → steel is more elastic; preferred in heavy machines and structures.
- Wood, bone, concrete and glass have rather small Y.
- A material that stretches less for a given load is more elastic (so steel is more elastic than rubber).
Shear modulus (G) or modulus of rigidity
- G = shearing stress / shearing strain = (F × L)/(A × Δx) = F/(A × θ); σs = Gθ.
- G is generally less than Y; for most materials G ≈ Y/3.
- Shear modulus and Young's modulus are relevant only for solids (only solids have definite length and shape).
Bulk modulus (B) and compressibility
- B = −p/(ΔV/V); the minus sign shows volume decreases as pressure increases; B is always positive.
- Compressibility k = 1/B = −(1/Δp)(ΔV/V): fractional change in volume per unit increase in pressure.
- B(solids) > B(liquids) > B(gases). Gases are about a million times more compressible than solids.
- Reason: tight coupling between neighbouring atoms in solids; weaker in liquids; very poor in gases.
- Bulk modulus applies to solids, liquids and gases.
Poisson's ratio
- Lateral strain = strain perpendicular to the applied force = Δd/d.
- Poisson's ratio = lateral strain / longitudinal strain = (Δd/d)/(ΔL/L); within the elastic limit they are proportional.
- Pure number; no units or dimensions; depends only on the nature of the material.
- Steel: 0.28-0.30; aluminium alloys: about 0.33.
Elastic potential energy in a stretched wire
- Work done against inter-atomic forces is stored as elastic PE.
- U = ½ × Y × strain² × volume = ½ × stress × strain × volume.
- Energy per unit volume u = ½ σ ε.
Applications of elastic behaviour
- Crane rope: A ≥ Mg/σy. For 10 tonnes with mild steel (σy ≈ 300 × 10⁶ N m⁻²), A ≈ 3.3 × 10⁻⁴ m² (radius about 1 cm); with a safety factor of about ten, radius about 3 cm. Ropes are made of many thin wires braided together for flexibility and strength.
- Beam sag: δ = Wl³/(4bd³Y). Use large Y; increasing depth d is more effective than breadth b (δ ∝ d⁻³, but only ∝ b⁻¹); keep span l small.
- A deep, thin bar can buckle; the I-section gives a large load-bearing surface and enough depth, and reduces weight and cost.
- Pillars with distributed ends support more load than pillars with rounded ends.
- Maximum height of a mountain ≈ 10 km: hρg must stay below the elastic limit of rock (about 30 × 10⁷ N m⁻², ρ = 3 × 10³ kg m⁻³).
Formula table
| Formula | Meaning of symbols | When to use |
|---|---|---|
Stress = F/A |
F restoring force, A area; unit Pa, [ML⁻¹T⁻²] | Any stress |
Longitudinal strain = ΔL/L |
dimensionless | Stretching/compressing |
Shear strain = Δx/L = tan θ ≈ θ |
θ in radians | Shearing |
Volume strain = ΔV/V |
dimensionless | Hydraulic compression |
Y = (F × L)/(A × ΔL) |
Y Young's modulus | Elongation of wires and rods |
G = F/(A × θ) = (F × L)/(A × Δx) |
G shear modulus | Displacement of a sheared face |
B = −p/(ΔV/V), k = 1/B |
p pressure, k compressibility | Volume change under pressure |
p = hρg |
h depth, ρ density | Pressure for bulk strain problems |
Poisson's ratio = (Δd/d)/(ΔL/L) |
d diameter | Lateral contraction |
U = ½ × stress × strain × volume, u = ½σε |
u energy per unit volume | Elastic energy stored |
A ≥ Mg/σy |
σy yield strength | Minimum rope or cable area |
δ = Wl³/(4bd³Y) |
b breadth, d depth, l span | Sag of a centrally loaded beam |
Important tables and comparisons
Stress, strain and moduli at a glance (NCERT Table 8.4)
| Type of stress | Strain | Shape change | Volume change | Modulus | State of matter |
|---|---|---|---|---|---|
| Tensile or compressive | ΔL/L | Yes | No | Young's modulus Y | Solid |
| Shearing | θ (pure shear) | Yes | No | Shear modulus G | Solid |
| Hydraulic | ΔV/V | No | Yes | Bulk modulus B | Solid, liquid and gas |
Young's modulus of some materials (NCERT Table 8.1)
| Substance | Y (10⁹ N m⁻²) | Yield strength (10⁶ N m⁻²) |
|---|---|---|
| Steel | 200 | 250 |
| Iron (wrought) | 190 | 170 |
| Copper | 110 | 200 |
| Aluminium | 70 | 95 |
| Bone | 9.4 | — |
Bulk modulus comparison (NCERT Table 8.3)
| Material | B (10⁹ N m⁻²) |
|---|---|
| Nickel | 260 |
| Steel | 160 |
| Copper | 140 |
| Mercury | 25 |
| Water | 2.2 |
| Air (at STP) | 1.0 × 10⁻⁴ |
Brittle vs ductile vs elastomer
| Material type | Key feature on the stress-strain curve |
|---|---|
| Brittle | Ultimate strength D and fracture point E are close |
| Ductile | D and E are far apart |
| Elastomer (rubber, aorta) | Large elastic region, no Hooke's law over most of it, no clear plastic region |
Diagrams to revise
- Fig. 8.1 Types of stress: (a) tensile, cylinder elongates by ΔL; (b) shearing, cylinder deformed by angle θ; (c) book pushed sideways; (d) sphere under hydraulic stress, volume changes, shape does not.
- Fig. 8.2 Stress-strain curve of a metal: O-A linear (Hooke's law), B yield point, C permanent set, D ultimate tensile strength, E fracture.
- Fig. 8.3 Aorta tissue: curve rises steeply, non-linear, no plastic region.
- Fig. 8.6 Beam loaded at the centre: sag δ = Wl³/(4bd³Y).
- Fig. 8.7 Beam cross-sections: rectangular bar, buckling of a thin deep bar, I-section.
- Fig. 8.8 Pillars: rounded ends vs distributed ends.
NEET traps in this chapter
- ⚠️ "More elastic" means stretches less for the same load: steel is more elastic than rubber, and Y(rubber) < Y(steel).
- ⚠️ Stress is not a vector, though force is.
- ⚠️ A wire hung from a ceiling carrying load F has tension F, not 2F.
- ⚠️ Hooke's law holds only in the linear part O-A, not all the way to the yield point B.
- ⚠️ Hydraulic stress changes volume only; shearing stress changes shape only.
- ⚠️ Y and G apply only to solids; B applies to solids, liquids and gases.
- ⚠️ Strain and Poisson's ratio have no units; moduli have the units of stress (Pa).
- ⚠️ To reduce beam sag, increase depth, not breadth (δ ∝ 1/d³).
Practice questions
Try each question, then check the answer key below. Get instant answers and explanations for more Mechanical Properties of Solids questions on TrackPrep.
Q1. A steel wire of length 2 m and cross-sectional area 1 mm² is stretched by a load of 100 N. If Young's modulus of steel is 2 × 10¹¹ N m⁻², the elongation of the wire is:
- (A) 0.5 mm
- (B) 1 mm
- (C) 2 mm
- (D) 0.1 mm
👉 Solve this and more Mechanical Properties of Solids questions on TrackPrep
Q2. Water (bulk modulus 2.2 × 10⁹ N m⁻²) is subjected to an extra pressure of 1.1 × 10⁷ N m⁻². The fractional decrease in its volume is:
- (A) 5%
- (B) 0.05%
- (C) 0.5%
- (D) 2%
👉 Solve this and more Mechanical Properties of Solids questions on TrackPrep
Q3. A steel wire (Y = 2 × 10¹¹ N m⁻²) is under a tensile stress of 2 × 10⁸ N m⁻² within the elastic limit. The elastic potential energy stored per unit volume of the wire is:
- (A) 2 × 10⁵ J m⁻³
- (B) 5 × 10⁴ J m⁻³
- (C) 4 × 10⁵ J m⁻³
- (D) 1 × 10⁵ J m⁻³
👉 Solve this and more Mechanical Properties of Solids questions on TrackPrep
Q4. On the stress-strain curve of a material, the ultimate tensile strength point and the fracture point lie very close to each other. The material is:
- (A) Brittle
- (B) Ductile
- (C) An elastomer
- (D) Perfectly plastic
👉 Solve this and more Mechanical Properties of Solids questions on TrackPrep
Q5. Which elastic modulus is relevant for solids, liquids and gases?
- (A) Young's modulus
- (B) Shear modulus
- (C) Modulus of rigidity
- (D) Bulk modulus
👉 Solve this and more Mechanical Properties of Solids questions on TrackPrep
Q6. How many of the following statements are correct?
- Stress is a vector quantity.
- Strain has no units and no dimensional formula.
- Hooke's law is valid only in the linear part of the stress-strain curve.
- For most materials, the shear modulus is about one-third of Young's modulus.
- The elastic tissue of the aorta obeys Hooke's law over most of its elastic region.
- Poisson's ratio of steel lies between 0.28 and 0.30.
- (A) 2
- (B) 3
- (C) 4
- (D) 5
👉 Solve this and more Mechanical Properties of Solids questions on TrackPrep
Q7. Match Column I with Column II.
| Column I | Column II |
|---|---|
| A. Young's modulus | i. Reciprocal of bulk modulus |
| B. Shear modulus | ii. Change in volume without change in shape |
| C. Bulk modulus | iii. Change in length under tensile or compressive stress |
| D. Compressibility | iv. Change in shape without change in volume |
- (A) A-iii, B-ii, C-iv, D-i
- (B) A-iv, B-iii, C-ii, D-i
- (C) A-iii, B-iv, C-i, D-ii
- (D) A-iii, B-iv, C-ii, D-i
👉 Solve this and more Mechanical Properties of Solids questions on TrackPrep
Q8. Assertion (A): Beams used in bridges and buildings are commonly given an I-shaped cross-section.
Reason (R): The sag of a centrally loaded beam varies as 1/d³ (d = depth), and the I-section gives enough depth and load-bearing surface while avoiding buckling and reducing weight.
- (A) Both A and R are true, and R is the correct explanation of A
- (B) Both A and R are true, but R is not the correct explanation of A
- (C) A is true, but R is false
- (D) A is false, but R is true
👉 Solve this and more Mechanical Properties of Solids questions on TrackPrep
Answer key
| Q1 | Q2 | Q3 | Q4 | Q5 | Q6 | Q7 | Q8 |
|---|---|---|---|---|---|---|---|
| B | C | D | A | D | C | D | A |
- Q1: ΔL = FL/(AY) = (100 × 2)/(10⁻⁶ × 2 × 10¹¹) = 10⁻³ m = 1 mm.
- Q2: ΔV/V = p/B = (1.1 × 10⁷)/(2.2 × 10⁹) = 5 × 10⁻³ = 0.5%.
- Q3: Strain = σ/Y = 10⁻³; u = ½σε = ½ × 2 × 10⁸ × 10⁻³ = 1 × 10⁵ J m⁻³.
- Q4: NCERT Section 8.4: D and E close means brittle.
- Q5: Only solids have definite length and shape; bulk modulus applies to all three states.
- Q6: Statements 2, 3, 4 and 6 are correct. Stress is not a vector; aorta tissue does not obey Hooke's law over most of its range.
- Q7: From NCERT Table 8.4 and Section 8.5.3.
- Q8: NCERT Section 8.6.
Got one wrong? Ask Jojo, the AI teacher, to explain it on a whiteboard: ask your doubt on TrackPrep
Practise Mechanical Properties of Solids on TrackPrep
- ✅ Page-wise NCERT MCQs for Mechanical Properties of Solids, with explanations
- ✅ Chapter-wise PYQs
- ✅ NCERT line-by-line lecture by Anmol Sir
- ✅ Jojo, the AI teacher, for any doubt, in Hindi, English or Hinglish
👉 Start practising Mechanical Properties of Solids on TrackPrep
Previous chapter: Gravitation · Next chapter: Mechanical Properties of Fluids · All chapters: NEET Physics chapter-wise notes and questions
Frequently asked questions
Is Mechanical Properties of Solids important for NEET 2027?
Yes. Physics has 45 questions (180 marks) in NEET, and this short chapter is very scoring. Questions on Young's modulus, bulk modulus, the stress-strain curve and elastic energy are direct and formula-based.
Which topics of Mechanical Properties of Solids should I revise first?
Start with types of stress and strain and the three moduli (Table 8.4). Then learn the stress-strain curve points (yield point, ultimate strength, fracture) and finish with Poisson's ratio and elastic energy per unit volume.
How do I revise Mechanical Properties of Solids quickly before NEET?
Revise the formula table and the stress-strain curve labels, then redo NCERT Examples 8.1, 8.4 and 8.5. A short set of timed numericals on ΔL, ΔV/V and energy density is enough to lock it in.
Where can I practise more Mechanical Properties of Solids questions?
On TrackPrep you get page-wise NCERT MCQs, chapter-wise PYQs and custom tests for this chapter. If a solution is unclear, ask Jojo, the AI teacher, to explain it on a whiteboard.
Are Mechanical Properties of Solids and elasticity the same thing?
Not exactly: elasticity is the main idea of Mechanical Properties of Solids, but the chapter covers more than elasticity alone. Elasticity is the property by which a body regains its original size and shape when the deforming force is removed. The chapter also covers plasticity (permanent deformation, as in putty or mud), stress and strain, Hooke's law, the stress-strain curve, the elastic moduli, Poisson's ratio, elastic energy and engineering applications.
What is stress in Mechanical Properties of Solids?
Stress is the restoring force per unit area that develops inside a body when a deforming force acts on it, so stress = F/A. Its SI unit is N m⁻² or pascal (Pa) and its dimensions are [ML⁻¹T⁻²]. It can be tensile or compressive (longitudinal), tangential (shearing) or hydraulic, and the symbol σ (sigma) is used for it, as in yield strength σy and ultimate tensile strength σu.
What is strain in Mechanical Properties of Solids?
Strain is the fractional change in the dimensions of a body caused by stress. Longitudinal strain = ΔL/L, shearing strain = Δx/L = tan θ ≈ θ, and volume strain = ΔV/V. Because strain is a ratio of two similar quantities, it has no units and no dimensions.
What do G and k stand for in Mechanical Properties of Solids?
G is the shear modulus (modulus of rigidity), defined as shearing stress divided by shearing strain, G = F/(A × θ); for most materials G ≈ Y/3. k is the compressibility, the reciprocal of the bulk modulus, k = 1/B, which gives the fractional change in volume per unit increase in pressure. In Hooke's law, stress = k × strain, the letter k is also used for the modulus of elasticity, so read the context.
Last updated: 21 November 2026.
- chapter notes
- physics
- class 11
- neet 2027
- notes
- mechanical properties of solids
